The Obvious Solution
For Global Challenges – SIVACON
Type testing in low-voltage switchgear is increasingly becoming an issue of prime importance worldwide. In future, there will be no other solution. But how far does one really have to go to a accomplish a type test? Often too far.
But that is now a thing of the past. With the “SIVACON Technology Partner concept, Siemens is bringing the versatile and type-tested SIVACON low voltage switchboard to your door.
To this end, Siemens has picked competent, local switchgear manufacturers and has appointed them SIVACON Technology Partners.
Your SIVACON Technology Partner will receive the concentrated know-how of Siemens at terms and conditions that only a local vendor is able to offer. For you, this means: SIVACON including type testing – faster, more flexibly and at lower cost than ever before.
Your advantage: “SIVACON Technology Partners”
These are qualified and permanently audited switchboard panel manufacturers, which Siemens has selected, close to you. This means that you always have the wealth of Siemens know-how at conditions that only a local supplier can offer. Fast, flexible and favorably priced.
As a power distribution board, SIVACON is available throughout the world and can be used at all power levels up to 7400 A, as withdrawable as well as plug-in and fixed-mounted units.
Always Flexible – SIVACON Adapts to your Requirements
Modular technology makes it possible to adapt SIVACON optimally to all requirements.
- Standard horizontal busbar position at the top of the cubicle
- Any components can be installed in the device compartments regardless of the busbar position and cubicle depth
- Requirement-oriented compartmentalization of functional units (Form 1 to Form 4 according to IEC 60439-1)
- Deep device compartments
Optimum Adaptation to Space Conditions
- Wall-mounted or free-standing
- Cables and busbars may be connected optionally from above or below
- Cabling compartments front- or rear-located
- Good accessibility of busbars
|Technical Data at Galance|
|Standard and Specification||Type-tested low-voltage switchgear||IEC 60439-1, DIN EN 60439-1|
|and control gear assembly (TTA)||(VDE 0660 Part 500)|
|Testing of response to internal faults||IEC 61641, VDE 0660 Part 500, Supplement 2|
|Creepage distances and clearances||Rated impulse withstand voltage (Uimp)||8 kV|
|Rated insulation voltage (Ui)||1000 V|
|Rated operational voltage (Ue)||up to 690 V|
|Rated currents (In)Busbars (3-pole and 4-pole)||Main horizontal busbars||Rated current||up to||≤ 7400 A|
|Rated peak withstand current (Ipk)||up to||≤ 375 kA|
|Rated short-time withstand current (Icw)||up to||≤ 150 kA, 1s|
|up to||≤ 120 kA, 3s|
|Vertical busbars for circuit breakers||Rated current||up to||≤ 6300 A|
|Rated peak withstand current (Ipk)||up to||≤ 250 kA|
|Rated short-time withstand current (Icw)||up to||≤ 100 kA, 1s|
|up to||≤ 80 kA, 3s|
|Vertical busbars for fixed-mounted design||Rated current||up to||≤ 1400 A|
|Rated peak withstand current (Ipk)||up to||≤ 163 kA|
|Rated short-time withstand current (Icw)||up to||≤ 65 kA*, 1s|
|up to||≤ 50 kA, 3s|
|Vertical busbars for in-line plug-in design (3NJ6)||Rated current||up to||≤ 2100 A|
|Rated peak withstand current (Ipk)||up to||≤ 110 kA|
|Rated short-time withstand current (Icw)||up to||≤ 50 kA*, 1s|
|Switchgear rated currents||Circuit breakers||up to||6300 A|
|Outgoing feeders||up to||630 A|
|Internal separation||Form 1 to Form 4||IEC 60439-1, Section 7.7, DIN EN 60439-1|
|Surface treatment||Frame parts||Galvanized/powder-coated/wet-painted|
|Degree of protection||To IEC 60529, EN 60529||IP 30 to IP 54|
|Dimensions||Height: 2200, 2600 mm (with busbar top unit)|
|Width: 400, 600, 800, 1000, 1200 mm|
|Depth: 600, 800, 1000, 1200 mm|
|* Rated conditional short-circuit current Icc up to 100 kA|